Background decorative image

What a Substation Does and the 6 Roles That Keep It Live

A substation changes voltage, switches power between circuits and protects the network when something fails. Every solar farm, battery site and wind farm connects through one, and LSP Renewables’ transmission desk recruits the engineers who design, energise and maintain them for National Grid ET, SSEN Transmission and SSE supply chains.

Key Takeaways

  • A substation steps voltage up or down, routes power between circuits and isolates faults through protection relays and circuit breakers.
  • GB transmission runs at 400 kV and 275 kV, plus 132 kV in Scotland, while distribution networks run at 132 kV and below in England and Wales, down through 33 kV and 11 kV to 400 V.
  • Six roles keep a substation live, covering project management, HV design, protection and control, commissioning, switching authorisation and maintenance.
  • The Senior Authorised Person (SAP) is the role that legally controls switching and safety documents on a live HV system.
  • Protection and control engineers are the slowest substation hire, because few engineers hold both relay setting and commissioning experience.

What a Substation Actually Does

A substation is the point on the grid where voltage changes, circuits join or split, and faults get cut off before they spread. It holds transformers, switchgear, busbars, circuit breakers, protection relays and control systems inside a secured compound or building.

Power leaves a generator at one voltage, travels long distances at a much higher voltage to cut losses, then steps down again before it reaches homes and businesses. Each of those changes happens at a substation. The same site also lets the network operator switch a circuit out for maintenance, reroute power around a fault and measure what’s flowing through every feeder.

What is the difference between a transmission and a distribution substation?

A transmission substation works at 400 kV or 275 kV, or 132 kV in Scotland, and moves bulk power across the country. A distribution substation works at 132 kV and below in England and Wales, stepping power down through 33 kV and 11 kV to the 400 V supply that buildings use.

That split decides who owns the asset and who you hire. Transmission substations belong to National Grid Electricity Transmission, SP Energy Networks or SSEN Transmission, while distribution substations belong to the regional DNOs. If you need a quick refresher on where transmission stops and distribution starts, the voltage boundary is the simplest test.

What equipment sits inside a substation?

A substation holds four groups of equipment, covering power transformers, switchgear and circuit breakers, protection relays, and control and communications systems. Transformers change the voltage, switchgear and breakers open and close circuits, relays detect faults, and SCADA links every device back to the network control centre.

Switchgear comes in two main forms. Air insulated switchgear (AIS) spreads out across an open compound, while gas insulated switchgear (GIS) packs the same function into a sealed building, which suits tight urban sites and offshore platforms.

Why Substations Matter for Renewable Projects

Every renewable project needs a substation, because solar farms, battery sites and wind farms generate at a lower voltage than the grid they export into. The project substation steps that voltage up to the connection voltage, protects the network from faults on site and gives the network operator a point it can switch.

That makes the substation the critical path on most renewable builds. A solar farm can finish its panels and inverters on time, but it earns nothing until the substation is built, tested and energised. Large hybrid sites, where solar and battery storage share one connection, put even more weight on the substation because both assets wait on the same switching point.

Why do substation programmes run late?

Substation programmes run late because they depend on long lead equipment, scarce specialist engineers and network operator witness testing. Transformers and switchgear carry long manufacturing slots, protection settings need sign-off from the network operator, and a missing commissioning engineer can hold an energisation date for weeks.

The people problem is the one clients control. The way large clients structure hiring across major substation programmes shows that teams briefed early reach energisation with the right engineers in place, while teams hired at mobilisation spend the first months filling gaps.

The 6 Roles That Keep a Substation Live

Six roles take a substation from design to safe daily operation. Some lead the build and leave at handover, others stay with the asset for its working life, and the SAP role spans both because nobody can switch a live HV system without authorisation.

What does a substation project manager do?

A substation project manager owns the programme, budget, contract and interfaces from award to energisation. The role coordinates civils, electrical installation, protection and commissioning contractors, manages the network operator’s outage windows and reports progress to the client and, on larger schemes, the transmission owner.

Substation PMs usually come from HV contracting or utility delivery backgrounds. The move from senior project manager to project director on HV works follows the same pattern, with accountability widening from one substation to a portfolio of schemes.

What does an HV design engineer do?

An HV design engineer produces the primary design of the substation, covering single line diagrams, equipment ratings, earthing, layout and cable routes. The design has to meet the network operator’s technical standards and the project’s fault level, so it sets the equipment order list that everything else follows.

What does a protection and control engineer do?

A protection and control engineer designs, sets and tests the relays that detect faults and trip circuit breakers in milliseconds. The role writes protection settings, builds the secondary wiring design, and proves every scheme works before energisation, which makes it one of the hardest HV roles to fill.

Hiring for these engineers takes longer than most clients expect, and the time it takes to hire protection and control engineers on 275 kV projects is a good benchmark for planning.

What does a commissioning engineer do?

A commissioning engineer tests every piece of installed equipment before the substation goes live, from transformer ratio and insulation tests to circuit breaker timing and full protection scheme trips. The engineer records every result, works through snags with the installer and supports the network operator’s witness tests.

What does a Senior Authorised Person do?

A Senior Authorised Person (SAP) controls switching and issues safety documents on a live HV system under the site’s safety rules. Nobody works on, or near, live HV plant without a permit from an authorised person, so a SAP vacancy can stop both commissioning and maintenance on the site.

SAP authorisation is site and voltage specific, so a SAP from one network can’t simply switch on another without assessment. That’s why SAP cover is a constant hiring need for renewable operators with sites spread across several DNO areas.

What does a substation maintenance engineer do?

A substation maintenance engineer keeps the site safe and available after handover. The role runs planned inspections, transformer oil sampling, switchgear servicing and relay testing, responds to faults and alarms, and works under the SAP’s switching control whenever plant must be isolated.

How to Staff a Substation Programme

Staffing a substation programme works best when you hire in the order the work needs people, not the order budgets get approved. Design and protection roles come first, commissioning follows the installation peak, and SAP and maintenance cover must be in place before energisation.

Step 1. Map the roles by phase, separating design, installation, commissioning and operation.

Step 2. Brief protection and control and HV design roles first, because they’re the longest searches and they set the equipment order.

Step 3. Confirm SAP cover and authorisation for the specific network and voltage before commissioning starts.

Step 4. Book commissioning engineers against the installation programme, with named reserves for witness test dates.

Step 5. Plan the handover to maintenance staff before energisation, so the asset never runs without an authorised person.

Grid investment will keep pressure on every one of these roles. The RIIO-T3 grid investment pipeline draws on the same HV engineers that renewable developers need for their own project substations.

Frequently Asked Questions

What is the main purpose of a substation?

A substation’s main purpose is to change voltage so power can move efficiently between generators, the transmission network and end users. It also switches circuits in and out for maintenance and isolates faults through protection relays and circuit breakers, which stops a single failure spreading across the grid.

What voltages do UK substations work at?

GB transmission substations work at 400 kV and 275 kV, plus 132 kV in Scotland. Distribution substations in England and Wales work at 132 kV and below, stepping down through 33 kV and 11 kV to the 400 V three-phase supply that homes and businesses use. Renewable project substations connect at whichever level the grid offer specifies.

Who owns substations in the UK?

Transmission substations belong to the three transmission owners, National Grid Electricity Transmission in England and Wales, SP Energy Networks in southern Scotland and SSEN Transmission in northern Scotland. Distribution substations belong to the regional DNOs. Renewable developers often own the project substation on their side of the connection point.

What qualifications does a substation engineer need?

Most substation engineers hold an electrical engineering degree or HNC/HND, and many hold or pursue Incorporated or Chartered Engineer status with the IET. Switching roles need authorisation under the site or network safety rules, and commissioning and protection roles need proven relay testing experience at the relevant voltage.

Why is a Senior Authorised Person so important?

A Senior Authorised Person is important because nobody can work on live HV plant without the safety documents a SAP issues. If a site loses SAP cover, commissioning and maintenance stop. SAP authorisation is specific to the network and voltage, so replacement SAPs need assessment before they can switch.

About the Author

John Martin is Divisional Manager for Onshore Renewables at LSP Renewables and leads the company’s UK transmission desk. He holds active programme relationships across National Grid ET, SSEN Transmission, SSE, AmcoGiffen and J. Murphy and Sons, and works with LSP’s grid team on HV, substation and grid connection recruitment across the UK.

Need substation engineers before your energisation date?

Talk to LSP’s grid connection recruitment team and we’ll find the HV, protection and SAP engineers your programme needs.

What a Substation Does and the 6 Roles That Keep It Live
16 Nov, 2026
Share

Related News

 What a BESS Is and the 5 Roles It Takes to Build One
20 Nov 2026
What a BESS Is and the 5 Roles It Takes to Build One
A BESS, or battery energy storage system, stores electricity in batteries and releases it to the gri...
What a DNO Does and Why Your Grid Connection Waits on It
18 Nov 2026
What a DNO Does and Why Your Grid Connection Waits on It
A DNO, or Distribution Network Operator, owns and runs the regional electricity network that carries...
How recruitment is changing: RITA and the future of talent partnerships
16 Nov 2026
How recruitment is changing: RITA and the future of talent partnerships
The way businesses recruit is changing, and so are their expectations of a recruitment partner. Alon...